|
KiCADKicad
|
|
|
|
FreeCADFree Software Foundation, Inc.
|
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outputs for eurorack power (2x8 2.54mm, +/- 12V, 5V, gate, control), so it's a 1 to 3 adapter.
Check your 3 modules' current draw before using it, as 3 hefty modules may strain your rack's power supply.
For low current draw modules this can be a very helpful board.
I include KICAD files, the gerber, and the files you'll need to 3D print the "cradle" for it in the project files below.
Read more about this project in this AudioDiWHY blog post: https://audiodiwhy.blogspot.com/2023/11/warm-floater-eurorack-power-strip.html.
NOTES:
For the 3D print, even after careful measurements and double checking FreeCAD's dimensions I still needed to scale my 3D print to102%. At 100% the board was a very tight fit. My 3D printer usually prints a bit small however.
Warm Floater Eurorack Power Extender
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(1)
More by AudioDIWHY
-
LFO Mini: CA3080 based LFO
I needed a small PCB for upcoming projects where a Low Frequency Oscillator will be required. I also...
-
LFO2 From "Electronics For Musicians"
Analog LFO with variable frequency and lots of modulation options based on an EFM ("Electronics for ...
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
BNC to 3.5mm x3 adapter board
I needed some BNC to 3.5mm conversion and didn't want to use unreliable and fragile adapters or cust...
-
Voltage Controlled Stereo Panner
This is a modular synthesizer stereo panner for audio or control voltages.This is a modular project ...
-
Dual Concentric Pots to 4x JST XH 3 pin males
Needed an easy way to add dual concentric pots to my project. The PCB featured here accommodates 2 c...
-
AS3364 Linear Quad VCA Experimenter's Board
The AS3364 is a low cost, easy-to-use quad linear VCA--4 high quality voltage controlled amplifiers ...
-
Dual SOIC 2164 VCA
Dual SSM 2164 VCA-SOIC versionA classic dual audio VCA design, details in the blog post:https://audi...
-
Dual SSM 2164 VCA-THT version
A classic dual audio VCA design, details in the blog post here:https://audiodiwhy.blogspot.com/2025/...
-
XIAO ESP32 HAT (IMU + Baro + SD card module)
103 1 1 -
-
Segmented 7 Segment LCD display shield for Arduino UNO
126 0 0 -
-
MIDI FORGE Maestro - Wavetable Board emulated using Raspberry Pi Zero 2W
483 0 3
